Ruby-Orifice Nozzle      Mist Nozzle      Air Atomizing (Siphon & Pressure) Nozzle

For Humidification Call CTM Today: Patrick Sweeney at 1 (905) 624-4823 ext. 116

Atomizing Nozzles

Control the Direction & Characteristics of Steam

A nozzle is a device designed to control the direction or characteristics of a fluid flow.

Nozzles are frequently used to control the rate of flow, speed, direction, mass, shape, and/or the pressure of the stream that emerges from them.

Ruby-Orifice 316 Stainless Steel Nozzle Series

 
NOZZLE ORIFICE FLOW RATE in GPM at PSI
model inch 400 800 1000 1200 1500 2000
ASI-4R 0.0040 .008 0.12 .014 .015 .017 .019
ASI-45R 0.0045 .010 0.15 .017 .019 .021 .024
ASI-5R 0.0050 .013 0.18 .020 .022 .024 .028
ASI-55R 0.0055 .015 0.22 .025 .027 .031 .035
ASI-6R* 0.0060 .016 0.23 .026 .028 .032 .037
ASI-8R 0.0080 .029 0.41 .046 .050 .056 .065
ASI-10R 0.0100 .045 0.64 .072 .079 .088 .0102
ASI-12R 0.0120 .057 0.82 .092 .101 .113 .130
ASI-15R 0.0150 .071 1.05 .120 .131 .147 .170

 
NOZZLE ORIFICE FLOW RATE in LPM at BARLPM
model mm 40 60 70 80 100 140
ASI-4R 0.11 .030 .045 .051 .056 .064 .072
ASI-45R 0.11 .049 .059 .066 .069 .077 .092
ASI-5R 0.13 .053 .068 .076 .082 .091 .108
ASI-55R 0.14 .068 .085 .093 .102 .114 .135
ASI-6R* 0.15 .072 .089 .097 .106 .119 .140
ASI-8R 0.20 .127 .161 .174 .188 .210 .248
ASI-10R 0.25 .201 .252 .273 .294 .328 .388
ASI-12R 0.30 .265 .320 .343 .375 .419 .496
ASI-15R 0.38 .269 .397 .454 .489 .547 .647



 

Back to Top



Mist Nozzle Series

Stainless Steel Orifice with Check Valve

PRESSURE FLOW RATE in GPM
psi 0.12" (slvr) 0.08" (blu) 0.06" (red)
40 .0114 .0082 .0061
500 .0127 .0092 .0096
600 .0145 .0106 .0074
700 .0164 .0119 .0079
800 .0185 0.132 .0092
900 .206 0.153 .0100
100 .0211 0.158 .0106

PRESSURE FLOW RATE in LPM
bar Ø0.3mm (slvr) Ø0.2mm (blu) Ø0.15mm (red)
28 .043 .031 .023
35 .48 .035 .026
42 .055 .040 .028
49 .062 .045 .030
56 .070 .050 .035
63 .078 .058 .038
70 .080 .060 .040


 

Back to Top



 

Siphon Nozzle

Air-Atomizing (Siphon & Pressure) Nozzle Series


MODULE SEAL TYPE APPLICATION
MATERIAL FEATURE
P Series:
P-1, P-2, P-3,
P-4, P-5, P-9,
P-11

Teflon Water &
Chemical
Brass or Stainless Steel
with Stainless Steel Orifice
Air Pressure:
3 to 50 PSI
MAXIMUM
100 PSI/700 kPa

Air Capacity:
.41 to 4.86 CFM

Flow Capacity:
.05 to 2.72 GPH
(.2 to 30 LPH)
S Series:
S-1, S-2, S-3,
S-4, S-5, S-9,
S-11
Rubber
O-ring
Water
only
Brass or Stainless Steel
with Stainless Steel Orifice
 

Back to Top